How to Build and Use a Magneto Magnet Charger

An at-home guide to building and using a magneto magnet charger
By H. L. Ritter
March/April 1978
Add to My MSN

Design for magnet recharger.
Provided by H.L. Ritter
Slideshow


Content Tools

Related Content

Profiles: McWhorter's Magneto Repair

Kevin McWhorter of McWhorters Antique Iron Repair takes his show on the road to service engine magne...

Who Built This Magnet Engine?

A Gas Engine Magazine reader is looking for his Magnet engine, which may have been built in Canada. ...

Profiles: Lightning Magneto

Lightning Magneto manufactures top quality replacement parts with a concentration on a full line of ...

Fairbanks-Morse Engine Resource Needed

Looking for information and technical details for a Fairbanks-Morse engine

The following includes tips on how to build and use a homemade magneto magnet charger.

The cores of the electromagnet are made of soft bar steel one inch in diameter and three inches long. They are secured to a steel base measuring 5-1/4 by 1-1/2 by 5/8 inch and are provided with pole pieces measuring 1-3/4 x 1-3/4 by 5/8 inch. All contacting surfaces should be absolutely flat and square so that there will be good metalic contact over the entire surfaces. Before the wire is wound on them, the magnet cores must be insulated. A spool may be formed by placing fiber or cardboard washers around each end of the magnet cores and then wrapping the magnet cores themselves with several layers of electricians tape. The winding for this recharger is for use on 6 or 12 volt direct current, from automobile storage batteries. Applying three layers of No. 12 double cotton covered magnet wire is preferred. However, No. 12 gauge copper thermoplastic covered type "TW" house and building wire will give satisfactory service and results. Wind the wire around the electromagnet cores as shown in the illustrations and then wrap tape around the windings, to hold them in place. Mount the recharger on a wooden base large enough to also hold a single pole switch and a binding post.

CAUTION, the switch is a must, as the recharger draws high amperage from the battery. As a result, the battery has a tendency to produce some flammable gas, and any sparks around the battery vents could cause a fire and/or an explosion. Therefore, do not connect or disconnect the lead wires from the battery when the recharger is turned on. The windings will heat up quickly when in use; therefore, the switch should be closed for only a few minutes at a time. When a magneto is taken apart for any reason, it must be assembled with the magnets in the same relative position as formerly, otherwise their polarity may be reversed and the magneto will be inoperative. The magnets must never be left off the magneto even temporarily, without placing a steel bar across their poles to serve as a keeper. Unless this is done, they will lose their magnetism rapidly. Re-magnetizing the magnets of a magneto that has become weakened through long use is a simple process.

It is important that unlike poles of the magneto magnets and of the electro magnets be brought together; i.e. the North pole of the magneto magnet to the South pole of the electromagnet and vice versa. To insure this, the current should be turned into the electromagnet and magneto magnet suspended over it on a string. Starting at a distance of about 12 inches, slowly lower the magneto magnet. As you begin to lower the magneto magnet towards the electromagnet, the magneto magnet will automatically seek the proper polarity by swinging around and will then be strongly attracted to the electromagnet.

In recharging, set the magnet on top of the recharger after its polarity has been determined, and rock the magnet back and forth on its pole edges a number of times. Then lay it on its side with its poles away from you and extending just beyond the far edges of the electromagnet poles. Apply a keeper to the magnet poles, switch off the current and withdraw the magnet sideways from the recharger. The keeper should remain in place until the magnet is reassembled on the magneto.


Previous | 1 | 2 | Next






Post a comment below.

 

Beth Beavers
6/27/2014 12:27:45 PM
Hi Greg, You can find a more up-to-date article that uses modern equipment with pictures of the design and construction at http://www.gasenginemagazine.com/equipment/make-your-own-magnet-charger.aspx

Greg
6/6/2014 9:17:08 PM
It would be very helpful if there were some pictures of the construction and use of this magnet charger.

jenny and philip white
6/15/2011 4:06:50 PM
Hi can any one help us. We have purchased a 1946 John Deere Lindaman BO crawler tractor, but the tracks are bad, We have phoned John Deere dealers in uk but have had no luck!!wie live in Dorset UK.Jenny








SUBSCRIBE TO GAS ENGINE MAGAZINE TODAY!
First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Gas Engine Magazine is your best source for tractor and stationary gas engine information.  Subscribe and connect with more than 23,000 other gas engine collectors and build your knowledge, share your passion and search for parts, in the publication written by and for gas engine enthusiasts! Every month Gas Engine Magazine brings you: restoration stories, company histories, and technical advice. Plus our Flywheel Forum column helps answer your engine inquiries!

Be sure to take advantage of the Square Deal Subscription Program.

  • No Missed Issues.

  • No Renewal Notices.

  • No Additional Cost.

The Square Deal Subscription Program is designed as a paperless transaction with automatic renewals at a preferred low rate.   With advanced electronic notification, a 100% satisfaction guarantee and an easy opt-out plan, the Square Deal Subscription Program is the best value, risk free, eco-friendliest way to subscribe.