POPULAR MECHANICS' BUILD YOUR OWN TRACTORS


January/February 1996
Add to My MSN

Chuck Peters' 'steel mule.'
Slideshow


Content Tools

Related Content

Any Information on This Gas Engine?

Reader Larry Helwig is looking for more info on this gas engine that has "OS Kelly Western" cast int...

Old Photograph of McCormick Deering-Binder and Farmall F-12

McCormick-Deering binder and Farmall F-12 fill out the scene in this old photograph.

Heartland Acres Tractor Ride Returns in 2012

The Heartland Acres Tractor Ride is on again for 2012.  Mark your calendars for Saturday June 9, 201...

Wants to See a Bradley Tractor

A reader from Wisconsin is looking for information on a 1940s Bradley tractor.

In our December 1994 edition (page 10), we reprinted an ad from an old Popular Mechanics, which advertised a packet of material to assist those inclined to send for it in building a homemade tractor. The ad had been sent to us by Jeff Klaverweiden, 98 Elm Street, Huntington, New York 11743, who was curious about it. A letter to Popular Mechanics had yielded no information about the ad, nor the plans advertised. After our reprint, however, we received a stack of responses to the appearance of this adit turned out that our subscribers had a lot more information at their fingertips than the staff at Popular Mechanics. Here is what we learned:

From Chuck Peters of N5564 Hwy 57, Hilbert, WI 54129, we received this photo of his tractor built from blue prints which appeared in the 1939 May and June Popular Mechanics. Chuck displays his restored tractor with copies of the original blue prints at shows. He writes,

'I have restored this tractor as close as I can to the original. This tractor is made of 1931 Model A Ford car transmission, 1931 Model AA Ford truck radiator, and Model A 4 blade fan, 1928 2 ton Reo speed wagon truck rear end, standard 6 volt starter and generator from a Model A Ford car, #60 roller bearing chain from transmission to Reo rear end, transmission output shaft - 16 tooth sprocket to 84 tooth sprocket on Reo speed wagon rearend, 2 drawbars -1 stationary lower swinging draw bar higher. Gas tank from a pre-1920 Buick car, muffler is a standard Model A Ford car. 4 speeds: 3 forward, 1 reverse, 2.25 mph - low gear 2.61 mph - medium gear 2.83 mph - third gear 8.5 mph. Reo speed wagon 3 to 1 gear reduction.

'Front wheels are 24' by 3' I.H.C. with by 1 skid ring, Model T Ford spindles and bearings. Rear wheels are 40' wagon tires inch thick by 4' wide. Spokes are x 1 angle iron. There are 12 spokes per wheel, and 20 lugs x 1 x 1 angle iron, 6 inches long. These lugs are spaced 6 inches apart. Rear wheels were made according to Popular Mechanics'' blueprints. I made the front and rear wheels on this tractor.

'Colors are: smoke gray body, black engine and transmission and radiator, safety red wheels, and safety red champion cast iron seat. This engine was started on gas 2 quart can on back of muffler hand pumped into carburetor, then switched to kerosene when engine was warmed up.

'This tractor pulled two 14 inch bottom plows in Calumet County heavy soil in low gear. It was equipped with individual hydraulic brakes and 2 clutches. One was a foot clutch and the other a hand clutch working off the foot clutch.

'Eugene Pilling of Stockbridge, Wisconsin, originally built this homemade tractor from blueprints purchased from the original inventor before they were published in the Popular Mechanics in May and June of 1939.

'In our Midwestern section of the United States, the words 'donkey' and 'steel mule' are used to paraphrase homemade tractors. The word 'steel mule' used with parenthesis is not the same as the trade name Steel Mule. Steel Mule on the wood sign indicates the explanation of the word.

'I belong to the Wisconsin Steam Engine Club of Chilton, Wisconsin. I show the tractor there every year, the second weekend of August. I have been traveling the state enjoying showing this rare tractor.'

Another subscriber, Jon Marti of 6262 147 Avenue SE, Lake Lillian, Minnesota 56253 sent us photocopies of the story in the May and June 1939 issues of Popular Mechanics, 'Tractor Built from Old Car Parts Without Machining.' The article appeared in two parts and claimed, 'Anyone can build the tractor as it consists of old car and truck parts so ingeniously selected that the assembling can be done with wrenches, a hack saw and a little welding, the latter being done for a few dollars by your local machine shop.'

Another copy of the article was sent by Luc Grenier, 2635 Chemin Grenier, Stanstead, Quebec, Canada JOB 3E0. He advises us that the plans appeared not only in the magazine, but also in Popular Mechanics' annual Farm Book, but he's unsure which year.

'They also had another plan to make a smaller garden tractor published in their 1949 Farm Book. The called it Farmette. This one used a Wisconsin engine, about 8 HP.'

R. C. Major is another Canadian subscriber who responded to the ad. He lives at 699 Fairmont Road in Winnipeg, Manitoba, Canada R3R 1B3 and wrote:

'I am an old geezer who never throws anything away, that is why I have the original magazine still in excellent condition. My collection only began a few years ago and consists of an antique garden tractor, walk behind model, a grain cleaner, a 1928 15 HP Fairbanks Morse on steel wheels, and 2 Ruston and Hornsby Mark 'CR's and 1 Mark 'CY.' I recently purchased a 1938 John Deere with a 3 HP Fairbanks Morse engine mounted on it, making it look like a Rumely. The builder of this replica will be driving it in any parades that he comes to, and when I am finished playing with it, it will be donated to the Morden-Winkler Museum here in Manitoba. Those were the terms agreed to at time of sale.'

Another reader, William Rees of R.R. 1, Box 24, Franklin, IL 62638 spotted the ad and sent us a copy of the booklet, 1939 version, published by PM. And finally, another reader sent us news of an even earlier version of the same concept, from the same magazine. Bob Seith of 116 Locust Place, Granville, Ohio 43023 had this to say:

'Clearly, building a tractor out of car parts was on the minds of folks at Popular Mechanics for quite some time. Seeing your item in the December (1994) issue, making reference to a PM ad from 1940, triggered something in my mind and made me dive into a stack of old magazines.

'These pages are from the Popular Mechanics Shop Notes for 1933. The article professes to tell you how to build a working tractor, using a Model T engine and two different transmissions. I don't know that there's really enough detail to go on, but the writer certainly exudes confidence.

'My father built a tractor from old car parts during the Depression, but I don't know what plans (if any) he used. He used to say it was held together with nuts and bolts, and that things worked loose pretty regularly. I never saw it; it was junked when he bought a (very) used Fordson sometime around 1940.

'Even if you had the parts for this project today, it would be foolish to use them on a 'made-at-home' tractor: They'd be too valuable as antiques. But it's fun to dream, anyway.'

To paraphrase the title of the 1933 article, it would certainly be difficult to go 'From Junkpile to Tractor for Fifty Dollars' in today's world! We thank those of you who responded for clearing up the mystery.

Unfortunately, we don't have permission to reproduce the articles or the plans in our magazine, but if your local library has old issues of Popular Mechanics, you ought to be able to look up these articles and find out the details!

We are grateful to our astute readers who responded with the information, and we are pleased that they shared what they knew. Since we are often asked by subscribers to furnish information from previous issues, we know the efforts involved in such research!


Previous | 1 | 2 | 3 | Next






Post a comment below.

 








SUBSCRIBE TO GAS ENGINE MAGAZINE TODAY!
First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Gas Engine Magazine is your best source for tractor and stationary gas engine information.  Subscribe and connect with more than 23,000 other gas engine collectors and build your knowledge, share your passion and search for parts, in the publication written by and for gas engine enthusiasts! Every month Gas Engine Magazine brings you: restoration stories, company histories, and technical advice. Plus our Flywheel Forum column helps answer your engine inquiries!

Be sure to take advantage of the Square Deal Subscription Program.

  • No Missed Issues.

  • No Renewal Notices.

  • No Additional Cost.

The Square Deal Subscription Program is designed as a paperless transaction with automatic renewals at a preferred low rate.   With advanced electronic notification, a 100% satisfaction guarantee and an easy opt-out plan, the Square Deal Subscription Program is the best value, risk free, eco-friendliest way to subscribe.